How to Install Refrigerator Plumbing
Normally the compression fittings come with the fridge. Attach the free end of the copper tubing to the valve. Continue to 2 of 7 below.
Required Tools for this Project
Now snake the tubing in backward, starting at the fridge so the coiled portion remains there. If so, your job is very easy. Usually, this will be at some other existing water hookup, like the water supply lines connected to your sink faucet or dishwasher. Continue to 2 of 7 below. How does a halogen light bulb work?
An Adapt-a-Tee is an ideal plumbing fitting for this purpose. MORE Adapt-A-Tees are easy to install, and they provide the extra line you need with the least amount of work possible. The type designed for copper pipe use simple compression fittings, and there are other types designed for attachment to CPVC or PEX water supply pipes.
Adapt-a-Tees can be used in many situations where you need an extra line. They come in various sizes to suit the job. You will also need a longer flex water supply tube to run from the water pipe to the refrigerator.
Measure the distance carefully, and buy a supply tube with plenty of length for the job. First, locate the shutoff valve under the kitchen sink where you want to connect the new water line. Shut off the water at the valve that controls the cold-water supply pipe to the faucet.
If there are no branch shutoff valves, you can turn off the water by closing the main water supply valve to the entire house. Installing a Water Line Is a Snap. Continue to 2 of 7 below. Continue to 3 of 7 below. Continue to 4 of 7 below. Disconnect the Existing Water Line. Disconnect the faucet supply tube from the shutoff valve. Use two sets of pliers to safely remove the tube—one to hold the valve and one to unscrew it. Be prepared for a small amount of MORE water leakage as you remove the valve—this is just the standing water in the water pipe, and it can easily be sponged up.
Continue to 5 of 7 below. Connect the Tee Adapter. Attach the Adapt-a-Tee adapter to the shutoff valve, tightening by hand at first. Then finish tightening a little more with pliers; sure to use another set pliers to hold the shutoff valve and prevent it from twisting on the pipe while you tighten it.
If you need to drill through floors or walls, check for air ducts, electrical wiring, plumbing or other possible impediments first. Figure 6 to 8 ft.
Then decide which one of three refrigerator water line connection options you will use: If you have CPVC plastic or steel pipes, add tee fittings made of the same material.
Add pipe compound to the threads to make it easier to tighten compression joints. It has a tiny shutoff valve that uses a sharp pointed metal rod to pierce the outer wall of the pipe when screwed inward.
Then you back out the rod and water flows through a tiny hole into the tubing. To begin, shut off the water at the main valve, then open the sink faucet and another lower level faucet to drain the pipe. Next, cut out a small section of the cold water pipe and solder in a copper tee. Cut a 3- to 4-in. Once the assembly has cooled, close the new valve and open the water main to check the fittings for leaks. To straighten coiled tubing not the entire roll , have a partner hold the end of the tube flat on the floor, then push the roll against the floor while unrolling to the length you need to go through the cabinets.
Now snake the tubing in backward, starting at the fridge so the coiled portion remains there. Then attach the tubing to the back of the cabinets every 2 to 4 ft. But do clamp the tubing to the fridge. Normally the compression fittings come with the fridge.
Imsges: hook up refrigerator water line
You'll want to use water lines that are already in place if possible, rather than attempting to install new pipes.
Measure the distance carefully, and buy a supply tube with plenty of length for the job. You will have to wait hours before you have ice. Attach one end of the copper tubing to the refrigerator's water pipe, using a nut and ferrule.
Shut off the water at the valve that controls the cold-water supply pipe to the faucet. In this eater, we ran the new refrigerator water line from hook up refrigerator water line the kitchen sink through cabinets. Sign Up for our newsletters! If you have CPVC plastic or steel pipes, add tee fittings made of the same material. Nc online dating, cut out a small section of the cold water pipe and solder in a copper tee.
- Free dating sites jackson tn
- Who is nathan sykes currently dating
- Matchmaking blacked out dying light
- Toronto dating websites free
- Therapists dating
- What first message online dating
- Catholic dating muslim man
- Reviews on interracial dating central
- Authentic dating site india
- Speed dating for under 25s
- Report dating site scams
- Dating mcclelland tins
- Guys just want hook up
- Examples of mens dating profiles
- Things to know about dating a british man
- Hilarious perks of dating me
- Puyallup dating site
- Polyamory married and dating watch free online
- Absolute dating notes
- Dating was the easiest mangahere