Shower drain installation in a few simple steps | Easy Drain

How to install a shower drain

bathroom drain hookup

What size vent pipes do I need? But once you have a starter hole, the job gets easier because the concrete has space to crack and break off. Did this article help you?

Adding a basement bathroom

Not Helpful 5 Helpful 5. Both work well and are about equally easy to use. We ran vent lines under the floor joists Photo 6 and framed in a lower ceiling later. You're helping people by reading wikiHow wikiHow's mission is to help people learn , and we really hope this article helped you. We recommend the use of Easy Clean Set for daily maintenance and cleaning of your shower drain. We used a no-hub cast iron Y-fitting to tie into our cast iron main.

Set the shower pan in place and measure from the walls to determine the exact location of the drain. Assemble the drain and trap without glue. Then set the pan in place again to check your work before you finally glue up the fittings.

The vent system is a lot simpler than the drain system. We ran vent lines under the floor joists Photo 6 and framed in a lower ceiling later. In most basements, you can tie your new vent system into the line that vents the laundry sink. Our plumbing inspector allowed us to connect our new 2-in. Before cutting a section out of the old steel vent, we installed extra metal strapping to support the pipe during and after cutting. Plumbing codes vary by locality.

The rules we give in this article generally follow the strictest codes. Your local rules may be more lenient about issues like vent sizing, the choice of fittings, etc. Use a T-fitting in drain lines to connect a horizontal pipe to vertical pipes. It can also be used to tie vent lines into horizontal drains or to join vent lines.

In the drain system, use a Y-fitting to connect horizontal pipes Photo 3. A Y-fitting can also be used in vent systems. Standard fittings have hubs that fit over pipes.

That saves labor and space. What size drainpipe should I use? The toilet requires 3-in. A vent L-fitting can be used anywhere in the vent system, but only in the vent system—never where waste flows. The other two types of L-fittings are OK for venting, too. A plumbing vent is kind of like the air intake on a gas can; it lets in air. Without venting, a slug of sewage racing through a waste line creates air pressure and vacuum in the pipe. That means noisy, gurgling drains.

Even worse, vacuum can suck all the water out of traps, allowing sewer gas to flow freely into your home. The maximum distance between the trap and vent depends on the diameter of the pipe. It still needs a vent, though. Can vents run horizontally?

Yes, but horizontal vent lines must be at least 6 in. What size vent pipes do I need? A typical bathroom like the one we show sink, toilet, shower or tub requires a 2-in. Avoid last-minute shopping trips by having all your materials ready ahead of time.

Read more on Bathroom Remodeling. A bathroom in the basement adds a lot of value to a finished basement. If you still have a leak after inverting the nut, here are the possible causes most likely first, least likely last: Not enough plumbers putty Nut is not tight enough but be careful not to overtighten either Nylon looking washer is not flat and needs to be replaced the new one will be a fiber material and look like cardboard Rubber washer has been damaged and needs to be replaced Since you want to fix the leak once and for all, I say go to home center and buy replacement fiber washer, rubber washer and if needed more putty.

Then you can hit all bases at the same time. Bring the old washers so you buy the right stuff. Plumbing supply shops will have these items as well. I'll add one more to retired guy's listBurr or rough opening on the bottom of the sink There is a plastic piece inside the connection here. I can take a pic. Not sure if I put this is in wrong. The tail piece grey going into the slip joint trap white has a plastic 1. Tighten the lock nut firmly so that the plumber's putty oozes out from beneath the drain flange.

Hook up the tailpiece to the P-trap beneath the sink. Tighten all of the slip nuts and test for leaks. Insert the pivot rod into the stopper hole in the back of the tailpiece.

Line it up with an insertion hole on the sink stopper. You have it connected properly when you move the clevis rod up and down and the stopper moves correspondingly in the sink. A nylon ball on the end of the pivot rod will reside in a hole on the tailpiece with correct assembly of the stopper and pivot rod.

Slide a washer over the pivot rod until it rests on the nylon ball. Slide the retaining nut onto the pivot rod and attach it to the tailpiece.

Do not fully tighten the nut at this point; just thread it on so it holds the nylon ball in place. Slide only one side of the u-shaped spring clip onto the end of the pivot rod. Next, slide the clevis strap onto the end of the pivot rod. Then slide the other side of the spring clip onto the rod behind the clevis strap to hold it on the rod.

Attach the clevis strap to the stopper lift rod on the sink. There is a nut on the clevis strap to adjust the height of the lift rod. The rod will move the clevis strap, the pivot rod and the stopper up and down.

Imsges: bathroom drain hookup

bathroom drain hookup

You can also have a plumber with special sensing equipment track the main drain, which avoids the risks of cutting into the wrong pipes in a slab-on-grade house.

bathroom drain hookup

This may be the case in renovation projects, where there a shower tray has been installed.

bathroom drain hookup

Plumbing supply shops will have these items as jbl hookup. Tighten the lock nut firmly so that the plumber's putty oozes out bathroom drain hookup beneath the drain flange. Follow the instructions included with the new sink and defer to the manufacturer's guidelines. In the drain system, use a Y-fitting to connect horizontal pipes Photo 3. She's also a property manager and writes on DIY projects. Do sinks have bathtoom on them? Thanks bathroom drain hookup letting us know.